Видео

❤❤❤❤❤❤❤❤

Mantap sekali idenya mas bro... Sehat terus dan terus berkarya.. 👍👍👏👏🙏🙏

❤hey man you are brilliant and very different and model with more futures nice but size is too small but good model diy weldone sir

Outstanding!

Bhai machine ka BP

Uma gambiarra de quinta 🤦‍♂️

Nice

Fantastic

❤

Awesome work and visionary planning

❤روعه

Amazing build For someone who wants to try building this DIY lathe, you need to consider the material cost tools and it going to take some elbow grease to build or you can buy a used metal lathe with the same cost if you built it from the scratch

Exelente modificasion

Salam kenal dari Indonesia

Mantap lah

Unicamente viendolo lo creo que un motor de limpiaparabrisas pueda servir para eso increible

Outstanding 🎉

Idol, saan nyo po nabili ang chuck nang lathe machihe mo at magkano po?

oh WOW, nice job

Wala nang silbi ang fan di na kayang palamigin ang tubig pero gud repair maenganyo ang mamimili...

Зачем горбатого лепите, станкостростроение относится к точному машиносроению со 2 классом точности, циркурярку, секарку , терку электрическую даже трактор собрать из узлов а сделать точный станок в домашних условиях нет

Bro can i ask a question please ? Looking at the lathe chuck from the front , which direction is it rotating ? Thanks 😁🤘

Parabéns pelo projeto ! Obrigado por compartilhar Abraços aqui do Brasil

Good concept other the feed line through the machined edge of the Circumference of the base ... then the whole flat surface could of been used as a thrust plate ... 😮😮😮😮

Legal, porém o lugar onde foi instalado a entrada da mangueira do segundo macaco cilindro ficou no lugar errado, deveria ser do lado e não embaixo.

❤

Vendo esse projeto percebi que da pra fazer uma bomba para calibrar bico injetor de caminhão .

muito bacana esse projeto 👋👋👋

❤

👌

I made a similar modification 30 years ago 👍

ты создал топливную аппаратуру😂

Mantap abangku👍👍👍

Quá trinh sáng tạo hay quá bạn ơi🎉🎉🎉

Good job

gostei muito da construçao do torno caseiro,muito bom mesmo, o video foi muito legal parabens.

👍👍👍...use a small jack as a stag and accumulate, then use a small jake pump to compress hydraulic oil and send it to the large jack. (It's a really great way of thinking..it's the same principle as Hydraulic pump system from the master pump of a large truck..) Details that the creator of the clip should emphasize to the audience are: The ball bearings of the non-return valve Must be very good at the bearing because when lifting a lot of weight The pressure will be greater. Must not miss it, it is dangerous. can cause disability..(thanks for clip)..👍👍👍💖💖💖

Not questioning him because I can see that it works- but why didn't he just drill thru the red jack top cylinder, thread that part, install pipe fitting, then weld red jack cylinder to red jack outer cylinder? Would have done the same thing with far less work.

Ok

油圧ホース取り付け場所間違いだろ すごく使いにくいと思う

show parabéns

good get good brother

Aqui existe un gran error garrafal.......😮😮😮😢😢😢😢😢

عمل راءع جدا

Top amigo 🎉🎉🎉 parabéns

Agora revendo o percebi que você usou o primeiro como bomba pra usar o segundo com mangueira não prá aumentar a força Boa ideia valeu!

É interessante com esse sistema acredito que potencializou a força do segundo macaco!(Jack) Valeu muito obrigado!

Cuales son las medidas de largo y ancho?

Is tarike ka phool aur mujhe bhi chahie tha kaise milega bhai vah batao please jawab do❤❤❤❤

Nice tito😊